Bu sayfa henüz seçili dilde mevcut değil. Orijinal içerik gösteriliyor.

Smart home firmware

Turn a common Wi-Fi board into an Apple Home device.

HomeHome.App firmware runs on ESP32 and ESP8266 boards you buy locally. Install it from your browser in about two minutes, add it to the Home app, and switch it on with Maker Credits.

Start here →How Maker Credits work

Free firmwareFree demo firstChrome or EdgeFrom USD 0.50 a credit

Devices

Pick what you want to build.

Each device is free firmware for a board you buy yourself. Open a guide for the board, the wiring and the setup.

ESP321–6 credits per device24-hour free demo

Bridge: Sonoff / eWeLink in Apple Home

Our firmware on a small ESP32 board talks to your eWeLink account and shows your devices in the Home app.

Open the Bridge guide → NodeMCU LoLin V38 zones10 credits

Castle Black: wired alarm sensors

Wired motion sensors, door contacts or smoke detectors in the Home app, with a notification the moment something happens.

Open the Castle Black guide → ESP32 DOIT DevKit2 level switches10 credits

Water Level Control

Two wire pairs in your tank, pool or aquarium. When the water reaches a pair, its switch turns on in Apple Home – and in Google Home if you want.

Open the Water Level guide → NodeMCU LoLin V31, 2 or 4 relays1–4 credits

Relay & Shutter

A NodeMCU board and a 2- or 4-channel relay module become a smart switch or roller shutter control for Apple Home and Google Home.

Open the Relay & Shutter guide →

Already have your Bridge board? Flash your Bridge in two minutes →

How it works

Four steps, from board to Home app.

Full setup guide →

STEP 1

Get the board for your device from any local shop: ESP32 DOIT DevKit, Wemos D1 R32 or D1 Mini ESP32 for the Bridge, ESP32 DOIT DevKit for Water Level Control, NodeMCU LoLin V3 for Castle Black and Relay & Shutter.

STEP 2

Flash it in your browser.

Plug the board in over USB, open the right flasher in Chrome or Edge on your computer and click Install. About two minutes – nothing to download or install.

STEP 3

Connect it and pair it.

Join the board's HomeHome Wi-Fi from your phone (password homehome), enter your home Wi-Fi and your Gmail address, then add it in the Home app with the code 111-88-111.

STEP 4

Activate and control.

Get Maker Credits and write your Gmail address in the order note. Then use your devices in the Home app – with Siri, scenes and automations.

Try it free first. Installing the firmware is free, and every device starts in demo mode by itself after setup – the Bridge for 24 hours, other devices usually for 10 to 20 on/off changes, depending on the device. Like it? Buy Maker Credits. When we have added them to your Gmail account, restart the device and it keeps working.

Maker Credits

Pay only for what you connect.

The firmware is free. Maker Credits switch it on. Each device uses a set number of credits; add them up for all your devices. The minimum is 10.

Device	Credits
Bridge, per connected eWeLink device (the Bridge itself: 0)	1–6
Castle Black wired alarm	10
Water Level Control	10
Relay, on/off (1, 2 or 4 channels)	1, 2 or 4
Roller shutter	3

Example: two 2x switches (4) + one thermostat (4) + one NSPanel (6) = 14 credits = USD 7.00 a month or USD 70.00 a year.

Monthly

USD 0.50 per credit a month

10 to 500 credits. Digital only. Cancel the renewal at any time.

Buy Monthly

Yearly · 2 months free

USD 5.00 per credit a year

10 to 500 credits. Digital only. Cancel the renewal at any time.

Buy Yearly – 2 months free

Activation: write your Gmail address in the order note. We add the credits to that Gmail account. How Maker Credits work →

Guides

Read first, flash second.

All guides →

Start here: your first HomeHome.App device

Choose a project, get an ESP32 or NodeMCU board, install the firmware from Chrome or Edge and activate it with Maker Credits.

Firmware downloads

Find the right flasher for your board, then click Install. About two minutes with Chrome or Edge.

Wired Sensor Bridge (Castle Black)

8 wired zones for Apple Home on a NodeMCU board. Pin guide, 3-step setup and rules.

NodeMCU Relay Switch & Roller Shutter

A NodeMCU board and a 2- or 4-channel relay as a smart switch or roller shutter control. Credits, wiring and setup.

Help

Stuck on a step? Ask us.

Tell us the board you have and where the flash stopped. We read every message.

Chat with us – quickest for a stuck flash.

Email

info@homehome.app

Can I try it before I buy?

Yes. Installing the firmware is free, and every device starts in demo mode by itself after setup – the Bridge for 24 hours, other devices usually for 10 to 20 on/off changes, depending on the device. Like it? Buy Maker Credits and write your Gmail address in the order note. When we have added the credits, restart the device and it keeps working.

Do you ship any hardware?

No. HomeHome.App sells Maker Credits (firmware activation) only. You buy a compatible ESP32 or ESP8266 board in your own country and install our free firmware from your browser.

Which browsers can flash the board?

Chrome or Edge on a Windows, macOS or Linux computer. Phones, tablets, Safari and Firefox cannot flash the board.

Does it work with Apple Home and Google Home?

All HomeHome.App devices work with Apple Home. Water Level Control and Relay & Shutter can also be added to Google Home. HomeHome.App is an independent product and is not certified by Apple or Google.

How do I cancel my subscription?

Go to your account › Dashboard › Subscriptions and cancel the renewal. Your credits stay active until the end of the period you paid for.

All questions →

Go on. Wake a board up.

Your board, our firmware, your smart home. Start with the setup guide, or ask us anything first.

Start here →Talk to us

AI asistanınızla sipariş verin

Ürünlerimizi, kargo ve iadeyi Claude'a sorun. Ödemeyi her zamanki gibi sitemizde yaparsınız.

Claude ile alışveriş yap